| Long description |
DTP34 "QuickCal" Automated Hand Scanning Densitometer
Automated Hand Scanning Densitometer for Calibration of Color Output Devices
QuickCal provides calibration and quality control for PostScript color copiers, color printers, and color proofing systems. The calibration of any color output device will drift over time, causing fluctuations in color and tone values. Colors may vary due to changes in room temperature, humidity, or changes in paper, toner, or other materials.The QuickCal automatic scanning densitometer ensures consistent, accurate color on every job.
Calibration Software Interface
The QuickCal interfaces directly with most calibration software through a direct cable link to a host computer.This enables a quick transfer of color measurements directly to your calibration software.
Simple, Step By Step Operation
• Output a calibration test print from a color printer or copier.
• Move instrument over test print.
• QuickCal sends density readings to the color control software via serial interface.
• Within minutes, the printer is calibrated and ready to deliver accurate, consistent prints.
Features
• Is supported by a majority of 3rd party software, RIP and printer manufacturers. Visit X Rite web site “Color Enabled” for information: www.x rite.com/support/partners.asp
• Status T color response (the industry standard for wideband reflection densitometers).
• Interfaces with PC, Macintosh and SGI platforms.
• Fast, time saving process – completes calibration in under five minutes.
• Measures paper, density and dot area
• Small desktop footprint.
• Accessories included:
calibration reference
getting started guide
interface cable
power supply (optional line cords)
Benefits
• Color consistency throughout a job and over time.
• Sharp, accurate color.
• Predictable, repeatable results.
• Quality control of on demand color including proofing, large format and color prints.
• Fast, easy to use system.
• No trial and error.
• Fewer service calls, lower overall costs.
Specifications
Measuring Geometry
Reflection: 0°/45° per ANSI/NAPM
IT2.17 and ANSI/ISO 5 4 multisensor
array
Measuring Area
2mm x 4mm, 2mm in the direction of
travel. Instrument must sit on sample
for accurate measurement.
Light Source
Lamp life, approx. 300,000
scans @ 11" (279.4mm)
Gas Pressure @ 2850°K
Receiver
Blue enhanced silicon photodiodes
Sample Characteristics
Patch size:
.400" (10.16mm) min. in direction of
travel by .350" 9mm min. wide.
1mm wide 1.0D contrast space
between patches or .5D min
difference between patches.
Measurement Rate
>6" (>154mm)/sec maximum
controlled by operator.
System Response
ANSI/ISO Status T
Output
Density, +Dot, Dot, or Reflectance.
Output has x10 capability.
Measurement Range
0.00D to 2.50D absolute
Linearity
±0.02D or ±2%, 0 to 2.5D
Repeatability
±0.01D, 0 to 2.5D
Inter Instrument Agreement
±0.02 or ±2%, 0 to 2.5D
Zero Stability
±0.01D max
I/O Connection
DB9 socket
USB (future)
Data Interface
Interface: RS 232 with baud rates
from 1200 to 19.2k
Protocol: X Rite RCI commands
Power Requirements
+12v @ 700ma
Environmental
Operating range:
+10°C (50°F) to +35°C (104°F);
30% to 60% RH.
RH ratings are non condensing
Physical Dimensions
Height: 4.83 cm (1.90 in)
Width: 6.10 cm (2.40 in)
Length: 11.55 cm (4.55 in)
Weight
165g. (5.8 oz.)
Provided Accessories
Calibration Reference
Getting Started Guide
Manual and Utilities CD
Interface cable: DB9S RS 232 or USB
AC Adapter
Optional Accessories
Mac Serial Adapter
Region Specific Line Cords
Europlug Line Cord |
